Engineering :: Metallurgy
|
|
|
|
|
101. |
Modulus of elasticity for steel is approximately |
A. |
1.2 x 106 kg/cm2 |
B. |
2 x 106 kg/cm2 |
C. |
12 x 106 kg/cm2 |
D. |
52 x 106 kg/cm2 |
E. |
78 x 106 kg/cm2 |
|
|
Answer: Option B
Explanation:
|
102. |
As per IS code, C 65 steel will have carbon percentage of |
A. |
0.065 percent |
B. |
0.6 to 0.7 percent |
C. |
6 to 7 percent |
D. |
00 to 70 percent |
E. |
None of the above |
|
|
Answer: Option B
Explanation:
|
103. |
Which of the following is high speed steel? |
A. |
T 55 Ni Cr 65 Mo 30 |
B. |
T 75 W 18 Co 6 Cr 4 |
C. |
T 10 Cr 5 Mo 75 V 23 |
D. |
T 75 W 18 Co 6 Cr 4 V 1 Mo 75 |
E. |
None of the above |
|
|
Answer: Option D
Explanation:
|
104. |
Which of the following temperatures represents the tempering temperature for C 30 steel? |
A. |
1700?C |
B. |
1400-1450?C |
C. |
860-890?C |
D. |
550-660?C |
E. |
100-150?C |
|
|
Answer: Option B
Explanation:
|
105. |
Capacity of a cupola is expressed in terms of |
A. |
Diameter of drum |
B. |
Height of drum |
C. |
Tons of castings it can produce in one charge |
D. |
Tons of coke it can take in one charge |
E. |
None of the above |
|
|
Answer: Option C
Explanation:
|
106. |
During first charge in cupola the time taken by material to melt is approximately |
A. |
10 minutes |
B. |
Half an hour |
C. |
1 hour |
D. |
2 |
E. |
5 to 6 hours |
|
|
Answer: Option D
Explanation:
|
107. |
Which of the following is fluxing material for cupola? |
A. |
Limestone |
B. |
Fluorspar |
C. |
Soda Ash |
D. |
Any of the above |
E. |
None of the above |
|
|
Answer: Option D
Explanation:
|
108. |
Volume of air required to melt one ton of cast iron in a cupola at N.T.P. is roughly |
A. |
10 cubic metres of air |
B. |
100 cubic metres of air |
C. |
1000 cubic metres of air |
D. |
10000 cubic metres of air |
E. |
100000 cubic metres of air |
|
|
Answer: Option B
Explanation:
|
109. |
Usually the capacity of cupola is |
B. |
1 to 5 tons |
C. |
10 to 100 tons |
D. |
100 to 500 tons |
E. |
500 to 1000 tons |
|
|
Answer: Option B
Explanation:
|
110. |
Which of the following furnaces is not used for non-ferrous materials |
A. |
Pit furnace |
B. |
Crucible furnace |
C. |
Cupola |
D. |
Oil fired tilting furnace |
E. |
Gas fired tilting furnace |
|
|
Answer: Option C
Explanation:
|
Read more:
|
|